Prg Best Boy Field Service Manual Manual de usuario Pagina 26
- Pagina / 120
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
18 BEST BOY 4000
®
SPOT LUMINAIRE FIELD SERVICE MANUAL
Other Errors
Error Code Explanation Solution
Ballast Errors: Parity, Overrun,
Bad Header, Msg Too Long
Various ballast errors Check ballast comm cable/connections
Ballast Heat Sink Over Temp Ballast too hot Check fans
Ballast Short Detected Short circuit on ballast output Check wiring
Ballast Timeout: Lamp Strike Lamp failed to strike Check igniter, lamp
CAN Comm Error
Stopped receiving CAN messages from
motion processor
Check CAN cables/connections, motor
control board
Crossload Timeout
Crossload execution took too long due to
error
Remove any incoming DMX, retry
Data not crossload format
Data in memory is not proper format for
crossload
Load software via computer
DMX busy: cancel crossload
Cannot execute crossload with traffic on
DMX line
Remove incoming DMX control for cross
load
DMX: UART transmit error Transmit buffer busy when trying to send Remove any incoming DMX, retry
Fuse Blown One or more fuses are blown Check fuse on specified board
Gobo out of zero range
When zeroing gobo wheels, the wheel is
too far away from zero to set the position
Move wheel closer to home position
before zero command
Head Fan Error Fan not running properly Check fan
In Free Mode: Can’t Lock Free mode is enabled
Use pan/tilt menu to change from "free"
to "lock"
Lamp Off
Fan Error: Cannot strike lamp while any
fan is in error state
Check fan, fan cabling
Lamp Off: Over Temperature Head temperature too high Check fans
Lamp over threshold
Lamp hours above recommended
maximum
Change lamp
Must Unlock via Free Option Lock is enabled
Use pan/tilt menu to change from "lock"
to "norm"
Plenum Fan Error Fan not running properly Check fan
PMD Motion Error
Mechanism's actual position is too far
from its commanded position
Check mechanism motion
Framing Motor Disabled Framing not running properly Recalibrate, check mechanism motion
Stack Fan Error
One or more stack fans not running
properly
Check fan, fan cabling
Temp over threshold Temperature too high Check fans/filters
Tip Fan Error Fan not running properly Check fan
UPE Fans Error
Upper Enclosure fans not running
properly
Check fan, fan cabling
Yoke Fan Error Fan not running properly Check fan
- BEST BOY 4000 1
- SPOT LUMINAIRE 1
- FOREWORD 3
- II BAD BOY 4
- Notes de sécurité 5
- Revision History 6
- TABLE OF CONTENTS 7
- VI BAD BOY 8
- INTRODUCTION 9
- Customer Service 10
- DESCRIPTION 11
- COMPONENTS 12
- Head and Enclosure Components 13
- Yoke Components 14
- Pan-Side Yoke Leg 15
- 8 BEST BOY 4000 16
- About Moiré Gobos 17
- 10 BEST BOY 4000 18
- TESTING & TROUBLESHOOTING 19
- About This Section 20
- Test Screen 20
- Test Sub-Menu Screens 21
- Mechanical Tests 22
- Group Tests 23
- TROUBLESHOOTING 24
- Mechanism Errors 25
- Other Errors 26
- Basic Troubleshooting 27
- 20 BEST BOY 4000 28
- MAINTENANCE 29
- EQUIPMENT HANDLING 30
- Wheel Stack 31
- Assembly 31
- Wheel Stack Road Case 31
- ROUTINE MAINTENANCE 32
- Removing Aft Cover 33
- Removing Yoke Leg Covers 34
- Cleaning Intake Filters 36
- Cleaning Lenses 37
- DO NOT use window cleaner! 38
- Cleaning Luminaire Exterior 39
- REMOVE AND REPLACE PROCEDURES 41
- Adjusting Lamp 43
- 40 BEST BOY 4000 48
- Designer Color Filter 48
- Wheel Hub 48
- Step 6. Replace Head Cover 49
- Replacing Front Glass 50
- Replacing Light Shield 51
- Replacing Head Fan 53
- Replacing Lamp Pinch Fan 55
- Replacing Rear Housing Fan 57
- Replacing Head Controller PCB 59
- "A" 60
- CRITICAL! 60
- Replacing Wheel Stack 61
- 54 BEST BOY 4000 62
- Captive Screw 62
- Lens Group 1 62
- Replacing Gag EOT Sensor 63
- Replacing Gag Wheel Motor 64
- Replacing Gag Index Motor 65
- Replacing a Zoom Sensor 66
- Replacing a Zoom Lens Motor 69
- Replacing Reflector 73
- Replacing UV/IR Filter 76
- Replacing AR Glass 78
- Replacing Ignitor 80
- TOP VIEW - CABLE LAYOUT 82
- Replacing Upper Enclosure Fan 83
- Replacing Ballast 85
- HOT RELAY DETAIL 86
- Replacing Ballast Fan 87
- Replacing Yoke Fan 88
- Replacing Pan/Tilt Driver PCB 90
- Replacing Tilt COT Sensor 92
- Pan/Tilt Driver PCB 95
- Replacing Pan Drive Mechanism 97
- 90 BEST BOY 4000 98
- Setting Pan/Tilt Belt Tension 100
- 24-9816-0765 Yoke Driver 101
- 94 BEST BOY 4000 102
- ILLUSTRATED PARTS BREAKDOWN 103
- OVERVIEW 104
- Torque Chart 105
- PARTS BREAKDOWN 106
- Best Boy Spares Kit 108
- 102 BEST BOY 4000 110
- 104 BEST BOY 4000 112
- 106 BEST BOY 4000 114
- TECHNICAL SPECIFICATIONS 115
- Best Boy 4000 Spot Luminaire 116
- 110 BEST BOY 4000 118
- Dallas Office 120
- Dallas, Texas 75247 120
Relacionado con productos y manuales para Encendiendo Prg Best Boy Field Service Manual
(104 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales