Prg Bad Boy Field Service Manual Manual de usuario Pagina 26
- Pagina / 115
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
18 BAD BOY
®
SPOT LUMINAIRE FIELD SERVICE MANUAL
Mechanism Errors
Errors will be shown after the mechanism sub-code, for example: PAN:Comm Error.
Other Errors
Error Code Explanation
Comm Error Error communicating with motion processor
Init Error Error during initialization of motion processor
Cal Error Error resetting position values in motion processor at beginning of calibration
Cal Timeout An action during calibration took longer than expected
No Stop Mechanism which calibrates to a physical stop did not find that stop
Sensor Stuck During calibration, could not find either edge of the sensor or the sensor did not turn off as expected
No Sensor During calibration, no sensor was found in the range of travel
Hall Sensor Edge Found sensor, but couldn't find far edge
Motion Error Mechanism's actual position is too far from its commanded position
Command Error Error while sending commands to the motion processor
Get Position Error Error when retrieving current position from motion processor
Spin Error Error while sending spin command to motion processor
Stop Spin Error Error while sending stop spin command to motion processor
Spin Stop Timeout Spinning mechanism did not come to rest in the given period
Error Code Explanation
Temp over threshold Temperature too high
Lamp over threshold Lamp hours above recommended maximum
Lamp Off Fan Error: Cannot strike lamp while any fan is in error state
Pan/Tilt Aux Encoder Error Auxiliary encoder value is too far from the main encoder value
Gobo out of zero range When zeroing gobo wheels, the wheel is too far away from zero to set the position
DMX busy: cancel crossload Cannot execute crossload with traffic on DMX line
Data not crossload format Data in memory is not proper format for crossload
DMX: UART transmit error Transmit buffer busy when trying to send
Crossload Timeout Crossload execution took too long due to error
CAN Comm Error Stopped receiving CAN messages from motion processor
Main Fan Error Main fan CAN messages not received or fan not running properly
UPE Fans Error Upper Enclosure fans not running properly
Pinch Fan Error Pinch fan not running properly
Stack Fan Error One or more stack fans not running properly
- SPOT LUMINAIRE 1
- FOREWORD 3
- II BAD BOY 4
- Notes de sécurité 5
- Revision History 6
- TABLE OF CONTENTS 7
- Appendix B. Wiring Diagrams 8
- INTRODUCTION 9
- Customer Service 10
- DESCRIPTION 11
- FEATURES 12
- Luminaire Models 13
- COMPONENTS 14
- Head and Enclosure Components 15
- Yoke Components 16
- Pan-Side Yoke Leg 17
- 10 BAD BOY 18
- 12 BAD BOY 20
- TESTING & TROUBLESHOOTING 21
- Test Screen 22
- Mechanical Tests 23
- Group Test 24
- TROUBLESHOOTING 25
- Mechanism Errors 26
- Other Errors 26
- Basic Troubleshooting 27
- Component Troubleshooting 28
- Fan/Cooling Issues 30
- Lens Issues 31
- Menu Display Issues 32
- Pan/Tilt Issues 33
- 26 BAD BOY 34
- MAINTENANCE 35
- EQUIPMENT HANDLING 36
- ROUTINE MAINTENANCE 38
- Removing the Aft Cover 39
- Removing the Enclosure Covers 40
- If using 43
- Cleaning the Lenses 44
- DO NOT use window cleaner! 45
- Cleaning the Reflector 48
- Cleaning the UV/IR Window 49
- REMOVE AND REPLACE PROCEDURES 50
- Adjusting the Lamp 52
- Replacing a Gobo 53
- EXPLODED VIEW 57
- Replacing the Front Glass 58
- Replacing the Wheel Stack 59
- 56 BAD BOY 64
- ORIENTATION 65
- REAR VIEW 65
- HEADER SIDE 65
- Replacing a Zoom Sensor PCB 67
- Replacing the Main Head Fan 70
- Be sure to align fan ducts 74
- Replacing the Reflector 75
- Replacing a 2A Fuse 76
- Replacing the 3A Fuse 77
- 70 BAD BOY 78
- CABLE LAYOUT - REAR VIEW 79
- 72 BAD BOY 80
- Do not disconnect cables 81
- Replacing the Ignitor PCB 82
- Figure 3-36 83
- 78 BAD BOY 86
- Setting Pan/Tilt Belt Tension 91
- ILLUSTRATED PARTS BREAKDOWN 93
- OVERVIEW 94
- PARTS BREAKDOWN 95
- Bad Boy Spares Kit 97
- 94 BAD BOY 102
- TECHNICAL SPECIFICATIONS 103
- Bad Boy Spot Luminaire 104
- (766 mm) 106
- 30.15" 106
- Photometric Data 108
- 8º Full Angle 109
- 40,000 beam Lumens 109
- Iris Full Open 109
- 34º Full Angle 110
- 48,000 beam Lumens 110
- 56º Full Angle 111
- 50,000 beam Lumens 111
- Operation at Reduced Power 112
- WIRING DIAGRAMS 113
- Version as of: June 23, 2011 114
- Production Resource Group 115
- Dallas Office 115
- Dallas, Texas 75247 115
Relacionado con productos y manuales para Encendiendo Prg Bad Boy Field Service Manual
(48 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales